Recent Posts

Pages: 1 ... 4 5 [6] 7 8 ... 10
51
Computer Problem / Re: Upgrade firmware Manic Moose for BRYSTON BDP-2
« Last post by Kastina on 15, 07, 2015, 14:15:55 »
We have to do the work themselves to the best.
52
ทำแบบนี้แล้วเครื่องจะลวนมั้ยครับ
53
เป็นข้อมูลที่มีประโยชน์มากครับ
54
อันล่าเป็น Key หรือครับ
55
อยากได้ที่บอกชื่อ MainBorad ด้วย
56
Computer Problem / Re: ติดตั้ง Windows 7 ผ่านพอร์ต USB 3.0
« Last post by Tomdy on 02, 06, 2015, 13:37:31 »
อยากลงwindowเองมานานละครับไม่อยากไปร้าน
57
Computer Problem / Activate Windows Server 2012 Evaluation to Full Version
« Last post by admin on 23, 05, 2015, 10:18:45 »
Activate Windows Server 2012 Evaluation to Full Version

Step 1. The very first step is to view the current edition. So open Command Prompt or Windows PowerShell in elevated mode (Run as Administrator) and type, DISM /online /Get-CurrentEditon as shown below. As you can see the current edition is Datacenter Evaluation.


Step 2. You can also view to which target edition you can upgrade.  To view the possible upgrade path, type DISM /online /Get-TargetEditions on elevated command prompt as shown below. As you can see the possible upgrade option is, Datacenter edition.


Step 3. To upgrade type DISM /online /Set-Edition:ServerDatacenter /productkey:XXXX-XXXX-XXXX-XXXX-XXXX /AcceptEula. X is your product key. As you can see below, it this command will upgrade the edition of Server to full version. Press Y to reboot.


You can now view the new Server edition by going into Server Manager.

Ref: http://www.mustbegeek.com/activate-windows-server-2012-evaluation-full-version/



58
Computer Problem / UCS C200 Series Power On After Power Failure
« Last post by admin on 14, 04, 2015, 07:35:48 »
We recently had a power cut in the office and our UCS C210 M2 server didn't automatically power back on.


Normally there's a setting in the BIOS along the lines of "After Power Failure: Power On". After trawling through every option in the BIOS I couldn't find anything relevant - it turns out the setting is actually in the CIMC.
To access the CIMC GUI you need to make sure it has been configured, you can reach the configuration settings for the CIMC when the server is powering via these steps:
Press ESC to view POST messages
Press F8 to enter CIMC config
Keep an eye out whilst the server powers on and press the keys at the appropriate times - it'll say on screen. You can then set an IP address, etc.
Once the server's powerd on, go to the CIMC IP address in a web browser, e.g. https://192.168.111.175. If you've not set a username and password the defaults are as follows:

Username: admin
Password: password

Select the Sever tab on the left hand side of the screen, then Power Policies and select the Power Restore Policy you want:

Click Save Changes and you're done.

ref : http://ccnp-v.blogspot.com/2012/01/ucs-c200-series-power-on-after-power.html
59
IoT & Network Solutions / Re: How To: Flush Your Local DNS Cache
« Last post by Bsakirazb on 31, 03, 2015, 16:41:34 »
I was brought back to everyday life.             
60
ถ้าไม่เป็นตัวเสียเงิน กำหนด30วัน แต่ใช้ได้ต่อนะ แต่ก่อนใช้มันจะให้กดอย่างอื่นก่อน
Pages: 1 ... 4 5 [6] 7 8 ... 10